How do I turn on UniFi Protect recording?
To change the recording quality settings for the Unifi Protect Mobile app: 1.
- Tap the Menu icon in the upper left corner of the Home screen and select Cameras.
- Tap the desired camera and tap the cog icon to open the camera settings.
- Tap Recording Quality to adjust the camera’s frame rate and image quality.
How do I save UniFi video protection?
Click on the scissors/clip icon just below the lower right corner of the video player (next to the trash/delete icon) on the right side of the time-lapse box page, click and drag to select and export the desired footage. [Click Download – lower right corner of the video player.
How do I record UniFi video?
Click Settings – lower left corner. Click NVR Settings in the upper left corner. [Click the Select by Default tab. Recording Path is the value of the UNIFI Video Recording Backup option “Recording Path”.
Can I run UniFi Protect on my own hardware?
Unifi Protect is Ubiquiti’s video security system. Like the UNIFI Access Point and Network components, the UNIFI Camera and Protection system is very easy to use. They rarely integrate together, but to be clear, you can use Unifi Protect by itself as well.
Can I use other cameras with UniFi Protect?
Can I add another brand of IP camera to my UNIFI Protect NVR? Unifi Protect does not support OnVIF. This means that only Ubiquiti Unifi cameras are supported.
What is UniFi Video?
Unifi Video is an obsolete product line. This application and its associated devices do not receive technical support in any way, including functional and security updates. Additionally, there are no additional updates to support the center content associated with UNIFI Video.
Where are UniFi cameras made?
Ubiquiti products are manufactured by contract manufacturers solely outside the United States. Logistics/ fulfillment is “primarily in China, and to a lesser extent Taiwan and the US. Additionally, approximately 2/3 of UBNT’s workforce is located outside the U.S.
How do I Unmanage my UniFi camera?
The reset button is located next to the camera’s Ethernet port. Accepted solutions
- Press and hold the reset button for 10 seconds.
- Release the button (LED stops shining).
- Do not disconnect the camera from the power supply during the reboot process.
- The camera will restore factory settings after a few minutes.
Does Ubiquiti make a thermostat?
Here we have introduced the Ubiquistat series of commercial Bacnet thermostats. Manufactured in Middleton, Wisconsin, the Ubiquistat line was built from the ground up to simplify Bacnet.
How do I add a cloud key to UniFi?
Use your Chrome browser to go to https://unifi.ubnt.com and log into the Unifi cloud. Install the browser ad activate the “Discover Cloud Key” option at the top to find your device. From here you can upgrade the firmware to adopt the cloud key.
What is camera RTSP?
RTSP stands for Real Time Streaming Protocol. With RTSP, you can pull a live video stream from a camera and display it from a variety of devices and programs. Its primary use is to pull video feeds from cameras to NVRs, viewing software, or home automation solutions.
How do I add a user to UniFi Protect?
To create a new role in Protection:.
- [Click Add Role in the upper right corner of the Roles menu.
- Enter the details of the new user role. Enter a name for the role.
- [Click Add Role in the [lower right corner] to create the new role. Once added, the new user role will appear in the role list.
Are UniFi security cameras good?
Overall the product is very good. Picture quality is outstanding and audio is clear. If you want to view many cameras on one PC at a time, you will need a 30+ year old, very powerful PC to view.
How do I change my ubiquiti password?
Log into the UNIFI controller. Go to Settings (gear icon at the bottom left of the page). Navigate to the Sites section (this is the default section to navigate to when navigating to the Settings page). Make the desired changes in the Device Authentication section at the bottom of the page.
How do I reset my LG G3 Flex?
Reset Button The reset button is used to reset the camera to factory defaults. Press and hold the Reset button for at least 10 seconds while turning on the camera. Mount the G3 Flex camera on a desktop or table top using the base mount alone.
How do I change my UniFi camera IP address?
Response (4)
- Click on the client on the left.
- Click on the flex camera to expand the Properties panel.
- Click on the Configuration gear.
- Expand the Network section.
- Turn on Fixed IP Address and then fill in the IP address below. The default is what the Flex currently has, but can be changed.
What is a NVR camera?
A Network Video Recorder (NVR) is a computer system that records video footage and stores it on a hard disk, mass storage device, or cloud storage. NVRs are paired with digital Internet Protocol (IP) cameras to create a video surveillance system.
Can I use Ubiquiti access point without controller?
UNIFI APs can run on their own without a controller unless a guest portal-like feature is enabled (the UNIFI controller can also act as a captive portal). If the controller is rebooted, the APS will not restart.
How do I access UniFi AP without a controller?
Start the application on your mobile device. It will prompt you for a user name and password. Default is UBNT/UBNT. Select a strong password to continue. Scroll down and enter your WiFi Name (SSID) and Password.
Is Ubiquiti a good brand?
Ubiquiti is a well-known networking brand. Most people are familiar with the company’s access point. These are the round antennas you can find around schools, businesses, and public spaces. But even for individual use cases and small businesses, the upfront investment is always a bit steep.
Is UniFi an American company?
(formerly Ubiquiti Networks, Inc.) is an American technology company founded in 2003 in San Jose, California. Now based in New York City, Ubiquiti manufactures and markets wireless data communications and wired products for business and home use under several brand names.
How do I reset my UVC G3?
For UVC -G3 cameras and G4 -POR recovery
- Disconnect the POR cable from the camera.
- Press and hold the Reset button and then turn on the camera.
- Wait at least 10 seconds. Or wait until the LED flashes rapidly three times.
- Release the reset button.
- The device will automatically reboot to the old firmware.
How do I reset my UVC G3 Dome?
Reset to factory defaults, hold the Reset button down for at least 10 seconds while turning on the camera. MicroSD reserved for future use. Unifi video camera can be wall or ceiling mounted.
Can you override a wireless thermostat?
Wi-Fi connectivity and smart thermostat All thermostats can be overridden so heating can be turned on or off regardless of temperature.
Is it easy to install smart thermostat?
For most homes, installation of the Google Nest thermostat is a simple DIY project that takes about 20-30 minutes. Use the Nest app as your main guide as its step-by-step instructions make it easy to install and wire the thermostat.
How do I access my UniFi cloud controller?
Log into the UNIFI controller, go to Settings, and click on Cloud Access on the left side. Turn on “Enable Cloud Access” and your UBNT credentials will be requested and enabled. Once you have done this, you can log in to https: //unifi.ubnt.com to see your connected Unifi controller.
How do I log into my local UniFi controller?
Windows users: Start > All Programs > ubiquiti unifi. 2. The UNIFI login screen will appear. Enter your administrator name and password in the appropriate fields and click Login.
Is RTSP outdated?
It is now outdated. With the rise of other alternatives and the flexibility they offer, the demand for RTSP has decreased significantly.
Is RTSP still used?
Over time, however, HTTP-based technologies using adaptive bitrate algorithms have overtaken RTSP and RTMP. Nevertheless, RTSP is still actively used in video surveillance today to capture feeds from IP cameras. It is important to note that RTSP for IP cameras and TVs are two completely different protocols.
How do I change Unifi controller owner?
How to change the ownership of Unifi Dream Machine Pro
- From the page where you found the version number, click Advanced at the bottom of the bottom left menu.
- On the Advanced page, click Transfer Owner. Select the new owner from the device user list and click Transfer. Note that this process is permanent.
How do I install Unifi protect on home assistant?
To add Unifi Protect to your Home Assistant installation, go to the Integration page in the Configuration panel, click +Add Integration, find Unifi Protect, and provide the host IP, port number, user name, and password to add the UNIFI Protect server by providing the host IP, port number, user name, and password.
Can I use other cameras with UniFi Protect?
Can I add another brand of IP camera to my UNIFI Protect NVR? Unifi Protect does not support OnVIF. This means that only Ubiquiti Unifi cameras are supported.
Where are Ubiquiti cameras made?
Ubiquiti products are manufactured by contract manufacturers solely outside the United States. Logistics/ fulfillment is “primarily in China, and to a lesser extent Taiwan and the US. Additionally, approximately 2/3 of UBNT’s workforce is located outside the U.S.
What is a UniFi Dream Machine Pro used for?
Dream Machine Pro (UDM Pro) is an enterprise-grade UNIFI OS console that provides a scalable networking experience and a comprehensive platform for multi-application use. UDM Pro is an all-in-one networking console that runs all Unifi OS applications, including networking and protection.
Does UniFi Dream Machine replace Cloud Key?
No, you do not need a cloud key or any other type of UNIFI controller when you have UDM-Pro. The controller and USG are integrated. The UDM-Pro is configured from the start for cloud control.
How do I find my UniFi NVR address?
If you can log on to the NVR from a computer, follow these steps
- In the lower left corner, locate and click on Settngs.
- In the new window, look to the upper left and click on NVR Settings.
- This will open a new black window on the right side. Look at the very top and you will find the IP address.
How do I UniFi protect locally?
You can access Unifi Protect by going to Unifi.ui.com and signing into your Ubiquiti SSO account. If you want to connect to Protect directly without going through Unifi.ui.com: make sure your computer and the Unifi OS Console are on the same network. Enter the IP address of the Unifi OS console into your web browser.
What is the default username and password for Ubiquiti UniFi?
TLDR: The default username and password for the ubiquiti unifi access point (and many other ubiquiti products) is
How do I know my UniFi password?
For the password, use the default password provided by UNIFI, and if in doubt, look at the bottom of the router (the orange device with the two antennas) and look for the 8-digit pin. That is the default password. It is printed there in big bold letters – you can’t miss it.
How do I reset my UniFi Flex?
Press and hold the reset button on the switch as you power up the switch. Press and hold the reset button for at least 10 seconds during startup. The LED pattern is as follows Blue white-off point dot.
How do I log into my ubiquiti camera?
The username is UBNT and the password is exactly as you say – under settings, general device password.
What is UniFi Video?
Unifi Video is an obsolete product line. This application and its associated devices do not receive technical support in any way, including functional and security updates. Additionally, there are no additional updates to support the center content associated with UNIFI Video.